Christian Lamparter
2017-07-22 21:27:11 UTC
This patch adds and enables the device-tree definitions for
both qcom,ipq4019-wifi blocks for the IPQ4019.
Support for these have been added into the ath10k driver since:
commit 280e762e9c72 ("ath10k: enable ipq4019 device probe in ahb module")
The binding documentation was added in:
commit a47aaa69de88 ("dt: bindings: add new dt entry for pre calibration in qcom, ath10k.txt")
This has been tested on an ASUS RT-AC58U (IPQ4019),
an AVM Fritz!Box 4040 (IPQ4018), a Compex WPJ428 (IPQ4028)
and a Cisco Meraki MR33 (IPQ4029).
| a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff [...]
| a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
| a000000.wifi: firmware ver 10.4-3.4-00082 api 5 features no-p2p,mfp,[...]
| a000000.wifi: board_file api 2 bmi_id 0:16 crc32 5773b188
| a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file [...]
...
| a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
| a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
| a800000.wifi: firmware ver 10.4-3.4-00082 api 5 features no-p2p, [...]
| a800000.wifi: board_file api 2 bmi_id 0:17 crc32 5773b188
| a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file [...]
Signed-off-by: Christian Lamparter <***@googlemail.com>
---
arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi | 8 +++
arch/arm/boot/dts/qcom-ipq4019.dtsi | 84 +++++++++++++++++++++++++++
2 files changed, 92 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
index c25d8f5c669d..cfa0c9970d5b 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
@@ -112,5 +112,13 @@
***@b017000 {
status = "ok";
};
+
+ ***@a000000 {
+ status = "ok";
+ };
+
+ ***@a800000 {
+ status = "ok";
+ };
};
};
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index d1a56331ce96..1ddcc96b510c 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -291,5 +291,89 @@
compatible = "qcom,pshold";
reg = <0x4ab000 0x4>;
};
+
+ wifi0: ***@a000000 {
+ compatible = "qcom,ipq4019-wifi";
+ reg = <0xa000000 0x200000>;
+ resets = <&gcc WIFI0_CPU_INIT_RESET>,
+ <&gcc WIFI0_RADIO_SRIF_RESET>,
+ <&gcc WIFI0_RADIO_WARM_RESET>,
+ <&gcc WIFI0_RADIO_COLD_RESET>,
+ <&gcc WIFI0_CORE_WARM_RESET>,
+ <&gcc WIFI0_CORE_COLD_RESET>;
+ reset-names = "wifi_cpu_init", "wifi_radio_srif",
+ "wifi_radio_warm", "wifi_radio_cold",
+ "wifi_core_warm", "wifi_core_cold";
+ clocks = <&gcc GCC_WCSS2G_CLK>,
+ <&gcc GCC_WCSS2G_REF_CLK>,
+ <&gcc GCC_WCSS2G_RTC_CLK>;
+ clock-names = "wifi_wcss_cmd", "wifi_wcss_ref",
+ "wifi_wcss_rtc";
+ interrupts = <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 38 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 39 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 40 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 41 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 42 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 43 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 45 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 46 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 47 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 168 IRQ_TYPE_NONE>;
+ interrupt-names = "msi0", "msi1", "msi2", "msi3",
+ "msi4", "msi5", "msi6", "msi7",
+ "msi8", "msi9", "msi10", "msi11",
+ "msi12", "msi13", "msi14", "msi15",
+ "legacy";
+ status = "disabled";
+ };
+
+ wifi1: ***@a800000 {
+ compatible = "qcom,ipq4019-wifi";
+ reg = <0xa800000 0x200000>;
+ resets = <&gcc WIFI1_CPU_INIT_RESET>,
+ <&gcc WIFI1_RADIO_SRIF_RESET>,
+ <&gcc WIFI1_RADIO_WARM_RESET>,
+ <&gcc WIFI1_RADIO_COLD_RESET>,
+ <&gcc WIFI1_CORE_WARM_RESET>,
+ <&gcc WIFI1_CORE_COLD_RESET>;
+ reset-names = "wifi_cpu_init", "wifi_radio_srif",
+ "wifi_radio_warm", "wifi_radio_cold",
+ "wifi_core_warm", "wifi_core_cold";
+ clocks = <&gcc GCC_WCSS5G_CLK>,
+ <&gcc GCC_WCSS5G_REF_CLK>,
+ <&gcc GCC_WCSS5G_RTC_CLK>;
+ clock-names = "wifi_wcss_cmd", "wifi_wcss_ref",
+ "wifi_wcss_rtc";
+ interrupts = <GIC_SPI 48 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 49 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 51 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 52 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 53 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 54 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 55 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 56 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 58 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 59 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 60 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 61 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 62 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 63 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 169 IRQ_TYPE_NONE>;
+ interrupt-names = "msi0", "msi1", "msi2", "msi3",
+ "msi4", "msi5", "msi6", "msi7",
+ "msi8", "msi9", "msi10", "msi11",
+ "msi12", "msi13", "msi14", "msi15",
+ "legacy";
+ status = "disabled";
+ };
};
};
both qcom,ipq4019-wifi blocks for the IPQ4019.
Support for these have been added into the ath10k driver since:
commit 280e762e9c72 ("ath10k: enable ipq4019 device probe in ahb module")
The binding documentation was added in:
commit a47aaa69de88 ("dt: bindings: add new dt entry for pre calibration in qcom, ath10k.txt")
This has been tested on an ASUS RT-AC58U (IPQ4019),
an AVM Fritz!Box 4040 (IPQ4018), a Compex WPJ428 (IPQ4028)
and a Cisco Meraki MR33 (IPQ4029).
| a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff [...]
| a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
| a000000.wifi: firmware ver 10.4-3.4-00082 api 5 features no-p2p,mfp,[...]
| a000000.wifi: board_file api 2 bmi_id 0:16 crc32 5773b188
| a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file [...]
...
| a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
| a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
| a800000.wifi: firmware ver 10.4-3.4-00082 api 5 features no-p2p, [...]
| a800000.wifi: board_file api 2 bmi_id 0:17 crc32 5773b188
| a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file [...]
Signed-off-by: Christian Lamparter <***@googlemail.com>
---
arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi | 8 +++
arch/arm/boot/dts/qcom-ipq4019.dtsi | 84 +++++++++++++++++++++++++++
2 files changed, 92 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
index c25d8f5c669d..cfa0c9970d5b 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
@@ -112,5 +112,13 @@
***@b017000 {
status = "ok";
};
+
+ ***@a000000 {
+ status = "ok";
+ };
+
+ ***@a800000 {
+ status = "ok";
+ };
};
};
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index d1a56331ce96..1ddcc96b510c 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -291,5 +291,89 @@
compatible = "qcom,pshold";
reg = <0x4ab000 0x4>;
};
+
+ wifi0: ***@a000000 {
+ compatible = "qcom,ipq4019-wifi";
+ reg = <0xa000000 0x200000>;
+ resets = <&gcc WIFI0_CPU_INIT_RESET>,
+ <&gcc WIFI0_RADIO_SRIF_RESET>,
+ <&gcc WIFI0_RADIO_WARM_RESET>,
+ <&gcc WIFI0_RADIO_COLD_RESET>,
+ <&gcc WIFI0_CORE_WARM_RESET>,
+ <&gcc WIFI0_CORE_COLD_RESET>;
+ reset-names = "wifi_cpu_init", "wifi_radio_srif",
+ "wifi_radio_warm", "wifi_radio_cold",
+ "wifi_core_warm", "wifi_core_cold";
+ clocks = <&gcc GCC_WCSS2G_CLK>,
+ <&gcc GCC_WCSS2G_REF_CLK>,
+ <&gcc GCC_WCSS2G_RTC_CLK>;
+ clock-names = "wifi_wcss_cmd", "wifi_wcss_ref",
+ "wifi_wcss_rtc";
+ interrupts = <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 38 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 39 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 40 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 41 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 42 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 43 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 45 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 46 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 47 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 168 IRQ_TYPE_NONE>;
+ interrupt-names = "msi0", "msi1", "msi2", "msi3",
+ "msi4", "msi5", "msi6", "msi7",
+ "msi8", "msi9", "msi10", "msi11",
+ "msi12", "msi13", "msi14", "msi15",
+ "legacy";
+ status = "disabled";
+ };
+
+ wifi1: ***@a800000 {
+ compatible = "qcom,ipq4019-wifi";
+ reg = <0xa800000 0x200000>;
+ resets = <&gcc WIFI1_CPU_INIT_RESET>,
+ <&gcc WIFI1_RADIO_SRIF_RESET>,
+ <&gcc WIFI1_RADIO_WARM_RESET>,
+ <&gcc WIFI1_RADIO_COLD_RESET>,
+ <&gcc WIFI1_CORE_WARM_RESET>,
+ <&gcc WIFI1_CORE_COLD_RESET>;
+ reset-names = "wifi_cpu_init", "wifi_radio_srif",
+ "wifi_radio_warm", "wifi_radio_cold",
+ "wifi_core_warm", "wifi_core_cold";
+ clocks = <&gcc GCC_WCSS5G_CLK>,
+ <&gcc GCC_WCSS5G_REF_CLK>,
+ <&gcc GCC_WCSS5G_RTC_CLK>;
+ clock-names = "wifi_wcss_cmd", "wifi_wcss_ref",
+ "wifi_wcss_rtc";
+ interrupts = <GIC_SPI 48 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 49 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 51 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 52 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 53 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 54 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 55 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 56 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 58 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 59 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 60 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 61 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 62 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 63 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 169 IRQ_TYPE_NONE>;
+ interrupt-names = "msi0", "msi1", "msi2", "msi3",
+ "msi4", "msi5", "msi6", "msi7",
+ "msi8", "msi9", "msi10", "msi11",
+ "msi12", "msi13", "msi14", "msi15",
+ "legacy";
+ status = "disabled";
+ };
};
};
--
2.13.3
2.13.3