[linux-sunxi][PATCH 0/2] Beelink X2 updates

[c***@gmail.com]

From: Marcus Cooper <***@gmail.com>

Hi all,
as support for sun8i H3 usb otg and ethernet patches has made it into mainline
then these patches extend the functionality of the device.
BR,
CK

Marcus Cooper (2):
ARM: dts: sun8i: h3: Enable USB OTG on the Beelink X2
ARM: dts: sun8i: h3: Enable dwac-sun8i on the Beelink X2

arch/arm/boot/dts/sun8i-h3-beelink-x2.dts | 32 +++++++++++++++++++++++++++++--
1 file changed, 30 insertions(+), 2 deletions(-)

[c***@gmail.com]

From: Marcus Cooper <***@gmail.com>

This STB has a type A socket which acts as OTG.

Signed-off-by: Marcus Cooper <***@gmail.com>
---
arch/arm/boot/dts/sun8i-h3-beelink-x2.dts | 23 ++++++++++++++++++++++-
1 file changed, 22 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
index e7fae65eb5d3..87d7f2cdefa6 100644
--- a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
+++ b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
@@ -100,6 +100,10 @@
};
};

+&ehci0 {
+ status = "okay";
+};
+
&ehci1 {
status = "okay";
};
@@ -147,10 +151,19 @@
status = "okay";
};

+&ohci0 {
+ status = "okay";
+};
+
&ohci1 {
status = "okay";
};

+&reg_usb0_vbus {
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
+};
+
&spdif {
pinctrl-names = "default";
pinctrl-0 = <&spdif_tx_pins_a>;
@@ -163,7 +176,15 @@
status = "okay";
};

+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
- /* USB VBUS is on as long as VCC-IO is on */
+ /* USB VBUS is always on except for the OTG port */
status = "okay";
+ usb0_id_det-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA07 */
+ usb0_vbus-supply = <&reg_usb0_vbus>;
};

[c***@gmail.com]

From: Marcus Cooper <***@gmail.com>

The dwmac-sun8i hardware is present on the Beelink X2.
It uses the internal PHY.

This patch create the needed emac node.

Signed-off-by: Marcus Cooper <***@gmail.com>
---
arch/arm/boot/dts/sun8i-h3-beelink-x2.dts | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
index 87d7f2cdefa6..a6c44b7043c5 100644
--- a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
+++ b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
@@ -53,7 +53,7 @@

aliases {
serial0 = &uart0;
- /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+ ethernet0 = &emac;
ethernet1 = &sdiowifi;
};

@@ -108,6 +108,13 @@
status = "okay";
};

+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;

[Maxime Ripard]

Post by c***@gmail.com
Hi all,
as support for sun8i H3 usb otg and ethernet patches has made it into mainline
then these patches extend the functionality of the device.
BR,
CK

Applied both, thanks!
Maxime